Full and nominal form ties for Western/aluminum forms. Manufactured from 14-gauge steel, these form ties have a tensile strength greater than 16,000 lbs. while standard form ties are only tested to a strength of 7500 lbs. Our form ties are galvannealed to prevent rust from forming on the tie, even when left outside. Extensive testing is done on every batch of steel to make sure they break off easily. Also, each pack of 100 comes with our easy-to-carry handle, so no longer will you have to deal with wire. Form ties are offered for 6”, 8”, and 10” wall widths. Manufactured at our facility, not bought and resold. Standard shipping is in boxes of 2,500, 10,000 form ties to a pallet. Minimum order quantity – 100 – Can only order in quantities of 100.

5/8” x 5/8” x 5/8” channel door frame spreader bar. Serves as support to the bottom of door frames for shipping and handling. 18 gauge galvanneal steel. Galvanneal coating is easy to weld in the bottom of frames. Cut to length.
$0.37 per foot. Minimum order quantity – 50 pieces.

12 gauge door closer reinforcement plate. All material is an easy to weld galvanneal. Cut to length.
If you are looking for a size not found below, please input required dimensions in the custom size box.

Also called glass bead or hollow metal glass stop. 10’ x 5/8” x 5/8” x 5/8” channel. All material is 18 gauge, easy to weld galvanneal. Gray paint is standard, beige/tan paint available upon request. Most of our stock is painted material, but unpainted glazing bead with only the galvanneal coating is also available. Countersunk holes are punched at 6”, 8”, 10”, or 12” intervals designed for a #8 TEK screw. 8” center-to-center hole spacing is industry standard.
Minimum order quantity – 50 pieces.

5/8” x 1 5/8” x 5/8” door channel reinforcement. All material is 18 gauge galvanneal.

Hat-shaped channel used as internal door stiffeners. 5/8” x 5/8” x 1 ½” x 5/8” x 5/8” 22 gauge cold rolled steel. Cut to length.

L x 1” x 1 ¼” x 1” 18-gauge galvanneal. 16-gauge galvanneal available in 4” and 6” lengths. Weld in Z shaped clip for securing hollow metal door frames to metal studs.

14-gauge galvanneal for 5 ¾” frame. Used for securing the mullion to the floor.

1” x 1 ½” 16-gauge galvanneal, ¼” holes. Generally used for anchoring door frames to the floor when no existing wall is available.

12 Gauge galvanneal. Tension held, twist in frame anchor for securing hollow metal door frames to existing masonry walls, no welding required. Sized only for 5 ¾” frames. Anchors for both unequal and equal rabbet frames available.

14-gauge galvanneal, tension held, twist in frame anchor for 5 ¾” and 8 ¾” frames. Anchors for both unequal and equal rabbet frames available. 8 ¾” frame anchors can be trimmed down for a variety of jamb sizes.

13” Electric lock box, 18-gauge steel with galvanneal coating. 7/8” knock outs with plugs on top and bottom for ½” conduit fittings. Used as a shield to protect from grout or mortar. Fits 2” face frame.

1 ¼” x 1 ¼” – 2” x 2” perforated steel angle with 3/8” holes 1” apart. Used when replacing or installing overhead door assemblies. All perforated angle is manufactured with a safety edge, preventing cuts from sharp angle edges. Formed from high tensile – low carbon steel. Gauges range in size between 16-gauge to 12-gauge. Punched angle has a bright Galvanneal or Galvanized coating to prevent corrosion over time. Offset angles and slotted holes are available at an extra cost.